Rigol DS6000 Series Manual do Utilizador descarregar pdf (Página 6)

Other accessories

Sample Mode

Real Time

Sample Rate

Equivalent

Sample Rate

Peak Detect

Averaging

High Resolution

Memory Depth

Number of

Channels

Input Coupling

Input Impedance

Probe

Attenuation

Coefcient

Maximum Input

Voltage (1MΩ)

Real-time Sample, Equivalent Sample

5 GSa/s (single-channel)

2.5 Gsa/s (dual-channel)

100 Gsa/s

200 ps (single-channel)

400 ps (dual-channel)

After all the channels nish N samples at the

same time, N can be 2, 4, 8, 16, 32, 64, 128,

256, 512, 1024, 2048, 4096 or 8192.

12 bits of resolution when ≥5 μs/div @ 5 GSa/s

(or ≥10 μs/div @ 2.5 GSa/s).

single-channel: Auto, 14k pts, 140k pts, 1.4M

pts, 14M pts and 140M pts are available

dual-channel: Auto, 7k pts, 70k pts, 700k pts,

7M pts and 70M pts are available

DS6XX4: four channels

DS6XX2: two channels

DC, AC or GND (Ground)

(1 MΩ±1%) || (14 pF±3 pF)

or 50 Ω±1.5%

0.001X, 0.01X, 0.1X, 1X, 2X, 5X, 10X, 20X,

50X, 100X, 200X, 500X, 1000X

Maximum Input Voltage of the Analog Channel

CAT I 300 Vrms, CAT II 100 Vrms,

Transient Overvoltage 1000V pk

with RP2200 10:1 probe: CAT II 300 Vrms

with RP3300 10:1 probe: CAT II 300 Vrms

with RP3500 10:1 probe: CAT II 300 Vrms

with RP5600 10:1 probe: CAT II 300 Vrms

Sample

Input

All the specifications are guaranteed except the parameters marked with “Typical” and

the oscilloscope needs to operate for more than 30 minutes under the specied operation

temperature.

Timebase Scale

Timebase Accuracy

Delay Range

Timebase Mode

Number of XYs

Waveform Capture

Rate

1

Bandwidth (-3dB)

Single-shot Bandwidth

Vertical Resolution

Vertical Scale

Offset Range

Bandwidth Limit

2

Low Frequency Response

(AC Coupling -3dB)

DC Gain Accuracy

DC Offset Accuracy

ESD Tolerance

Channel to Channel

Isolation

DS606X: DC to 600 MHz

DS610X: DC to 1 GHz

DS606X: DC to 600 MHz

DS610X: DC to 1 GHz (each channel)

8bits, two channels sample at the

same time

2 mV/div to 5 V/div (1 MΩ)

2 mV/div to 1 V/div (50 Ω)

2 mV/div to 120 mV/div: ± 1.2V (50 Ω)

125 mV/div to 1 V/div: ± 12V (50 Ω)

2 mV/div to 225 mV/div: ± 2V (1MΩ)

230 mV/div to 5 V/div: ± 40V (1MΩ)

20 MHz or 250 MHz

≤5 Hz (on BNC)

±2% full scale

200 mV/div to 5 V/div:

0.1 div ± 2 mV±0.5% offset value

2 mV/div to 195 mV/div:

0.1 div ± 2 mV±1.5% offset value

±2 kV

DC to maximum band width: >40 dB

Horizontal

Vertical

Trigger

Trigger Level Range

Trigger mode

Holdoff Range

High Frequency Rejection

2

Low Frequency Rejection

2

Edge Trigger

Edge Type

Pulse Trigger

Pulse Condition

Pulse Width Range

Slope Trigger

Slope Condition

Time Setting

Rising, Falling, Rising&Falling

Positive Pulse Width (greater than, lower than,

within specic interval)

Negative Pulse Width (greater than, lower than,

within specic interval)

4 ns to 4 s

Positive Slope (greater than, lower than,

within specic interval)

Negative Slope (greater than, lower than,

within specic interval)

10 ns to 1 s

Internal

EXT

Auto, Normal, Single

100 ns to 10 s

50 kHz

5 kHz

± 6 div from center screen

± 0.8 V

DS606X: 1 ns/div to 50 s/div

DS610X: 500 ps/div to 50 s/div

≤ ±(15 + 2 ×instrument age in years) ppm

Pre-trigger (negative delay): ≥1 screen width

Post-trigger (positive delay): 1 s to 1000 s

Y-T, X-Y, Roll, Time Delayed

2 simultaneously

150,000 wfms (vector display);

180,000 wfms (dots display)

Battery power option

1 2 3 4 5 6 7 8

Comentários a estes Manuais

Sem comentários