Rigol DS1000Z Series Especificações Página 64
- Página / 172
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
RIGOL Chapter 2 Command System
2-50 DS1000Z Programming Guide
:MEASure Commands
DS1000Z can measure the following 24 waveform parameters and provide the statistic function for the
measurement results. In additional, you can use the frequency counter to make more precise measurement
of the input signal frequency. :MEASure commands are used to set or query the corresponding parameters.
Time Parameters
Period:
Defined as the time between the threshold middle points of two consecutive,
like-polarity edges.
Frequency:
Defined as the reciprocal of period.
Rise Time:
The time for the signal amplitude to rise from the lower limit to the upper limit of
the threshod.
Fall Time:
The time for the signal amplitude to fall from the upper limit to the lower limit of the
threshod.
+ Width:
The time difference between the threshold middle points of a rising edge to the
next falling edge of the pulse.
- Width:
The time difference between the threshold middle points of a falling edge to the
next rising edge of the pulse.
+ Duty:
The ratio of the positive pulse width to the period.
- Duty:
The ratio of the negative pulse width to the period.
Delay and Phase
Delay 1→2 :
The time difference between the rising edges of source 1 and source 2. Negative
delay indicates that the selected rising edge of source 1 occurred after the selected
edge of source 2.
Delay 1→2 :
The time difference between the falling edges of source 1 and source 2. Negative
delay indicates that the selected edge of source 1 occurred after the selected edge
of source 2.
Phase 1→2 :
Phase difference calculated according to “Delay 1→2 ” and the period of source
1, expressed in degree. The calculation formula is shown following.
Phase 1→2 :
Phase difference calculated according to “Delay 1→2 ” and the period of source
1, expressed in degree.The calculation formula is shown following.
360
1
Delay
Phase
Period
= ×°
RiseTime
FallTime
Threshold Upper Limit
Threshold Middle Point
Threshold Lower Limit
+Width
-Width
Period
- Programming Guide 1
- Guaranty and Declaration 3
- Document Overview 4
- Contents 5
- RIGOL Contents 6
- Contents RIGOL 7
- DS1000Z Programming Guide V 7
- Remote Control Methods 12
- SCPI Command Overview 13
- Parameter Type 14
- Command Abbreviation 14
- Chapter 2 Command System 15
- :AUToscale 16
- :SINGle 17
- :TFORce 17
- :ACQuire Commands 18
- :ACQuire:MDEPth 19
- :ACQuire:TYPE 20
- :CALibrate Commands 21
- :CHANnel<n> Commands 22
- :CHANnel<n>:COUPling 23
- :CHANnel<n>:DISPlay 23
- :CHANnel<n>:INVert 23
- :CHANnel<n>:OFFSet 24
- :CHANnel<n>:RANGe 24
- :CHANnel<n>:TCAL 25
- :CHANnel<n>:SCALe 26
- :CHANnel<n>:PROBe 26
- :CHANnel<n>:UNITs 27
- :CHANnel<n>:VERNier 27
- :CURSor Commands 28
- :CURSor:MANual 29
- :CURSor:MANual:SOURce 30
- :CURSor:MANual:TUNit 30
- :CURSor:MANual:VUNit 30
- :CURSor:MANual:AX 31
- :CURSor:MANual:BX 31
- :CURSor:MANual:AY 31
- :CURSor:MANual:BY 32
- :CURSor:MANual:AXValue? 32
- :CURSor:MANual:AYValue? 32
- :CURSor:MANual:BXValue? 32
- :CURSor:MANual:BYValue? 33
- :CURSor:MANual:XDELta? 33
- :CURSor:MANual:IXDELta? 33
- :CURSor:MANual:YDELta? 33
- :CURSor:TRACk 34
- :CURSor:TRACk:AX 35
- :CURSor:TRACk:BX 35
- :CURSor:TRACk:AY? 35
- :CURSor:TRACk:BY? 36
- :CURSor:TRACk:AXValue? 36
- :CURSor:TRACk:AYValue? 36
- :CURSor:TRACk:BXValue? 36
- :CURSor:TRACk:BYValue? 37
- :CURSor:TRACk:XDELta? 37
- :CURSor:TRACk:IXDELTA? 37
- :CURSor:AUTO:ITEM 38
- :CURSor:XY 39
- :CURSor:XY:AY 40
- :CURSor:XY:BY 40
- :CURSor:XY:AXValue? 40
- :CURSor:XY:AYValue? 41
- :CURSor:XY:BXValue? 41
- :CURSor:XY:BYValue? 41
- :DISPlay Commands 42
- :DISPlay:DATA? 43
- :DISPlay:TYPE 44
- :DISPlay:GRADing:TIME 44
- :DISPlay:WBRightness 44
- :DISPlay:GRID 45
- :DISPlay:GBRightness 45
- IEEE488.2 Common Commands 46
- a decimal integer 48
- :MATH Commands 49
- :MATH:DISPlay 50
- :MATH:OPERator 50
- :MATH:SOURce1 50
- :MATH:SOURce2 51
- :MATH:SCALe 51
- :MATH:OFFSet 52
- :MATH:INVert 52
- :MATH:RESet 52
- :MATH:FFT:WINDow 53
- :MATH:FFT:SPLit 53
- :MATH:FFT:UNIT 54
- :MATH:FFT:HSCale 54
- :MATH:FFT:HCENter 55
- :MATH:OPTion:STARt 55
- :MATH:OPTion:END 56
- :MATH:OPTion:INVert 56
- :MATH:OPTion:SENSitivity 57
- :MATH:OPTion:DIStance 57
- :MATH:OPTion:ASCale 57
- :MATH:OPTion:THReshold1 58
- :MATH:OPTion:THReshold2 58
- :MASK Commands 59
- :MASK:SOURce 60
- :MASK:OPERate 60
- :MASK:MDISplay 61
- :MASK:SOOutput 61
- :MASK:OUTPut 62
- :MASK:X 62
- :MASK:Y 62
- :MASK:CREate 63
- :MASK:PASSed? 63
- :MASK:FAILed? 63
- :MASK:TOTal? 63
- :MASK:RESet 63
- :MEASure Commands 64
- Source 1 65
- Source 2 65
- :MEASure:SOURce 67
- :MEASure:COUNter:SOURce 67
- :MEASure:COUNter:VALue? 67
- :MEASure:CLEar 68
- :MEASure:RECover 68
- :MEASure:ADISplay 69
- :MEASure:AMSource 69
- :MEASure:SETup:MAX 70
- :MEASure:SETup:MID 70
- :MEASure:SETup:MIN 71
- :MEASure:SETup:PSA 71
- :MEASure:SETup:PSB 72
- :MEASure:SETup:DSA 72
- :MEASure:SETup:DSB 72
- :MEASure:STATistic:DISPlay 73
- :MEASure:STATistic:MODE 73
- :MEASure:STATistic:RESet 74
- :MEASure:STATistic:ITEM 74
- :MEASure:ITEM 75
- :REFerence Commands 76
- :REFerence<n>:SOURce 77
- :REFerence<n>:VSCale 77
- :REFerence<n>:VOFFset 78
- :REFerence<n>:RESet 78
- The default unit is V 89
- :SYSTem Commands 90
- :SYSTem:ERRor[:NEXT]? 91
- :SYSTem:GPIB 91
- :SYSTem:LANGuage 91
- :SYSTem:LOCKed 91
- :SYSTem:PON 92
- :SYSTem:OPTion:INSTall 92
- :SYSTem:OPTion:UNINSTall 92
- :TIMebase Commands 93
- :TIMebase:DELay:SCALe 94
- :TIMebase[:MAIN]:OFFSet 94
- :TIMebase[:MAIN]:SCALe 95
- :TIMebase:MODE 95
- :TRIGger Commands 96
- :TRIGger:COUPling 97
- :TRIGger:STATus? 97
- :TRIGger:SWEep 97
- :TRIGger:HOLDoff 98
- :TRIGger:NREJect 98
- :TRIGger:EDGe 99
- :TRIGger:EDGe:LEVel 100
- :TRIGger:PULSe 101
- :TRIGger:PULSe:WIDTh 102
- :TRIGger:PULSe:UWIDth 102
- :TRIGger:PULSe:LWIDth 103
- :TRIGger:PULSe:LEVel 103
- :TRIGger:SLOPe 104
- :TRIGger:SLOPe:TIME 105
- :TRIGger:SLOPe:WHEN 105
- :TRIGger:SLOPe:TUPPer 106
- :TRIGger:SLOPe:TLOWer 106
- :TRIGger:SLOPe:WINDow 107
- :TRIGger:SLOPe:ALEVel 107
- :TRIGger:SLOPe:BLEVel 108
- :TRIGger:VIDeo 109
- :TRIGger:VIDeo:MODE 110
- :TRIGger:VIDeo:LINE 110
- :TRIGger:VIDeo:STANdard 111
- :TRIGger:VIDeo:LEVel 111
- :TRIGger:PATTern 112
- :TRIGger:PATTern:LEVel 113
- :TRIGger:DURATion 114
- :TRIGger:DURATion:WHEN 115
- :TRIGger:DURATion:TUPPer 115
- :TRIGger:DURATion:TLOWer 116
- :TRIGger:TIMeout (Option) 117
- :TRIGger:TIMeout:TIMe 118
- :TRIGger:RUNT (Option) 119
- :TRIGger:RUNT:WHEN 120
- :TRIGger:RUNT:WUPPer 120
- :TRIGger:RUNT:WLOWer 121
- :TRIGger:RUNT:ALEVel 121
- :TRIGger:RUNT:BLEVel 122
- :TRIGger:WINDows (Option) 123
- :TRIGger:WINDows:POSition 124
- :TRIGger:WINDows:TIMe 124
- :TRIGger:WINDows:ALEVel 125
- :TRIGger:WINDows:BLEVel 125
- :TRIGger:DELay (Option) 126
- :TRIGger:DELay:SLOPB 127
- :TRIGger:DELay:TYPe 127
- :TRIGger:DELay:TUPPer 128
- :TRIGger:DELay:TLOWer 128
- :TRIGger:SHOLd (Option) 129
- :TRIGger:SHOLd:PATTern 130
- :TRIGger:SHOLd:TYPe 130
- :TRIGger:SHOLd:STIMe 131
- :TRIGger:SHOLd:HTIMe 131
- :TRIGger:NEDGe (Option) 132
- :TRIGger:NEDGe:IDLE 133
- :TRIGger:NEDGe:EDGE 133
- :TRIGger:NEDGe:LEVel 133
- :TRIGger:RS232 (Option) 134
- :TRIGger:RS232:WIDTh 136
- :TRIGger:RS232:BAUD 136
- :TRIGger:RS232:BUSer 136
- :TRIGger:RS232:LEVel 137
- :TRIGger:IIC (Option) 138
- :TRIGger:IIC:WHEN 139
- :TRIGger:IIC:AWIDth 139
- :TRIGger:IIC:CLEVel 141
- :TRIGger:IIC:DLEVel 141
- :TRIGger:SPI (Option) 142
- :TRIGger:SPI:WHEN 143
- :TRIGger:SPI:WIDTh 143
- :TRIGger:SPI:DATA 143
- :TRIGger:SPI:TIMeout 144
- :TRIGger:SPI:SLOPe 144
- :TRIGger:SPI:CLEVel 144
- :TRIGger:SPI:DLEVel 145
- :WAVeform Commands 146
- :WAVeform:SOURce 147
- :WAVeform:MODE 148
- :WAVeform:FORMat 148
- :WAVeform:DATA? 149
- :WAVeform:XINCrement? 150
- :WAVeform:XORigin? 150
- :WAVeform:XREFerence? 150
- :WAVeform:YINCrement? 151
- :WAVeform:YORigin? 151
- :WAVeform:YREFerence? 151
- :WAVeform:STARt 152
- :WAVeform:STOP 152
- :WAVeform:PREamble? 153
- Chapter 3 Programming Demos 155
- Programming Preparations 156
- Excel Programming Demo 157
- Matlab Programming Demo 161
- LabVIEW Programming Demo 163
- Visual C++ Programming Demo 169
Manuais e produtos relacionados com Medição, teste e controlo Rigol DS1000Z Series
(97 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais